Universal Expansion Joints — The Expansion Joints Blog

Archive

Tied Universal EJ with Control Rods for an Oil Recovery Project

July 9th, 2012 Comments off

Tied Universal EJ with Control Rods for an Oil Recovery Project

This tied universal expansion joint with control rods was designed for an oil recovery plant in Canada. It is 48″ in diameter and 68″ in overall length. This expansion joint was designed for 1″ compression, 4″ lateral and 15 psig at 150°F. The pipe was fabricated from A-36 carbon steel material and the bellows were fabricated from 316L stainless steel. A dye penetrant exam, air and soap test, along with a vacuum test was conducted prior to shipping.

Universal Tied Expansion Joint, 48″ Dia. and 141″ OAL, for Service in an Acid Regeneration Plant

May 7th, 2012 Comments off

Universal Tied Expansion Joint, 48" Dia. and 141" OAL, for Service in an Acid Regeneration Plant

A tied universal expansion joint was custom designed for service in an acid regeneration plant in Louisiana. It is 48″ in diameter, 141″ in overall length and designed for 1″ axial movement, 2-1/2″ lateral movement and .33° angular rotation. The expansion joint is fabricated with 310 stainless steel bellows, and 301 SS liner, duct, flanges, transition duct and covers. It was designed for 10 psig at 1150°F, and was dye penetrant examined, hydro-tested at 15 psig, and the bellows and pipe longitudinal weld seams were 100% x-rayed.

42″ Dia. Stainless Steel Expansion Joints for an Offshore Application

April 9th, 2012 Comments off

42" Dia. Stainless Steel Expansion Joints for an Offshore Application

These universal metallic expansion joints were custom designed for an offshore application. They are 42″ diameter, 24″ overall length and designed for 2″ axial movement and 1-1/2″ lateral movement. The expansion joints are fabricated entirely from 316 L stainless steel and designed for 1,000°F and 1 psig. Each unit was 100% dye penetrant examined and soap and air tested prior to shipment.

12″ Dia. Universal Expansion Joints with Stainless Steel Bellows

March 26th, 2012 Comments off

12" Dia. Universal Expansion Joints with Stainless Steel Bellows

These universal metallic expansion joints were custom designed for a chemical plant in Texas. They are fabricated entirely from stainless steel with 304 stainless steel bellows. The expansion joints are 12" diameter, 77-1/2" long and designed for 4-1/2" axial movement and 2" lateral movement. They were designed for 200°F and 100 psig. Each unit was 100% dye penetrant examined and hydrotested prior to shipment.

Tied Universal Expansion Joints Designed for a Power Generation Plant in Texas

August 22nd, 2011 Comments off

Tied Universal Expansion Joints

This week’s feature is on tied universal expansion joints designed for piping in a power generation plant in Texas. They are 6″ in diameter, 60″ in length, and will be used in a hot air application. The pipe, lugs and weld ends are fabricated from carbon steel, and the bellows are 321 stainless steel. The expansion joints are designed for 100°F at 3 psig and are capable of 6″ lateral movement. Each unit was 100% dye penetrant tested and soap and air tested prior to shipment.

Hinged Universal Expansion Joint and Duct Work Assembly Custom Designed for an Exhaust Duct Application

July 25th, 2011 Comments off

Custom Universal Expansion Joint and Duct Work Assembly

 

This week’s featured product is on a hinged universal expansion joint and duct work assembly custom designed for an exhaust duct application in a power plant in Kenya. The hinge hardware was fabricated from carbon steel, while the rest of the unit was fabricated from 316 stainless steel with Inconel 625 bellows. An F-type variable spring was also provided for this project and will be used to support the center spool between the two elbows. The duct work with expansion joint is 36″ in diameter and the distance between the centerline of the two 90 degree elbows is 240″. It is designed for 20 psig at 115°F and 1/2 degree of angular movement. The entire assembly was 100% dye penetrant tested and a soap and air test was performed prior to shipment.

Custom Universal Expansion Joint and Duct Work Assembly F Type Variable Spring

Axial and Lateral Movements on Universal Expansion Joints

July 18th, 2011 Comments off

The universal expansion joint consists of two bellows separated by a pipe section or spool. The primary purpose of this arrangement is to have a unit which will accept large amounts of lateral deflection. The amount of lateral deflection they can accept is a function of the amount of angulation each bellows can absorb and the distance between the bellows. For a given bellows element, the amount of lateral deflection capability can be increased or decreased by simply changing the length of the center spool. In our Expansion Joint Catalog, three standard overall lengths are given with their lateral movement capability. If the piping problem requires greater capability, then the overall length can be increased to suit.

Universal Expansion Joint Drawing

Since deflections are the result of piping thermal expansion, and universal expansion joints are usually long, our units are designed so that the thermal expansion within the tie rods is absorbed as axial compression by the two bellows elements. In this way, the overall length of the unit does not change when the piping is in service. The standard units in our Expansion Joint Catalog have all been designed to accept the thermal expansion of their length within the tie rods when the temperature is up to the design temperature shown.

You can view some of our past universal expansion joints on our blog.

Universal expansion joints are usually supplied with tie rods. Tie rods connect the ends of the unit to each other and restrain the pressure thrust load. This unit cannot accept any externally applied axial deflections. The thermal expansion of the distance between the tie rods —within the expansion joint— will be taken by the bellows element, as described above. The tie rods usually come in sets of two or more, equally distributed around the circumference of the expansion joint. When only two are provided, 180 degrees apart, the expansion joint is free to bend, or deflect angularly, as well as laterally. With three or more tie rods, since rods are loaded equally by the pressure thrust, only lateral deflections are possible without significant forces being applied by the adjacent piping.

See more pictures of universal expansion joints in our photo gallery.

72″ Double Gimbal and Single Hinged Flanged and Flued Head Expansion Joints

July 11th, 2011 Comments off

72 Inch Universal Gimbal and Single Hinged Flanged and Flued Head Expansion Joints

U.S. Bellows designed and fabricated a 180″ long double gimbal expansion joint with a 90° elbow and flanged and flued head bellows, and a 114″ long single hinged expansion joint with flanged and flued head bellows. After performing a pipe stress analysis on the line, it was determined that spring supports were necessary, so F-Type variable spring supports were also provided for this project and shipped with the expansion joints.

All material in contact with the service fluid is fabricated from 304 H stainless steel and all external hardware is 304 stainless steel. The expansion joint bellows is designed for 5° angular movement and 1100°F at 10 psig. A spot x-ray test, soap and air test, and 100% dye penetrant examination on all welds were performed prior to shipment.

Universal Rectangular Expansion Joint for a Mining Operation

June 27th, 2011 Comments off

Universal Rectangular Expansion Joint for a Mining Operation

This universal rectangular expansion joint is fabricated entirely of carbon steel with COR-TEN™ steel bellows for a mining operation in the mountains of Chile. COR-TEN™ steel is high strength and ideal for resisting corrosion. It measures 73-1/4″ L x 52″ W x 96″ H, weighs 2,700 lb. and was painted with universal shop primer. This expansion joint was 100% dye penetrant tested, and a soap and air test was performed prior to shipment.

90 inch Universal Flanged and Flued Head Expansion Joint and Duct Work Assembly

June 13th, 2011 Comments off

90 inch Universal Flanged and Flued Head Expansion Joint and Duct Work Assembly

This universal flanged and flued head expansion joint and duct work assembly is designed for a 90″ diameter line. It includes slotted hinge plates installed across the bellows to carry the weight of the duct between the bellows and equalize the axial compression between the two bellows. The flanged and flued heads, duct and weld ends are fabricated from 304 H stainless steel. The expansion joint is designed for 2″ axial compression, 2-1/2″ lateral deflection, and 1150°F at 5 PSIG. A spot x-ray test, soap and air test, and 100% dye penetrant exam were performed prior to shipment.

border

Contact Us: +1 (281) 241-9418 Toll Free: (855) 591-0906 Fax: +1 (713) 731-8640 sales@usbellows.com
Our Parent Company: Piping Technology Pipe Supports, Pipe Clamps, Pipe Hardware & Insulated Pipe Shoes
Fellow Subsidiaries: Sweco Fab: ASME Vessels, Pig Launchers, Duct Work, Strainers & Spectacle Blinds
 Pipe Shields: Pre-Insulated Pipe Supports, Slides, Guides & Anchors

Fronek Anchor/Darling
: Snubbers, Sway Struts & Sway Braces


Copyright © 2017  U.S. Bellows, Inc. All Rights Reserved. Privacy Policy